ASTM B505 PDF

June 23, 2020 0 Comments

ASTM B BM 08 Standard Specification for Copper Alloy Continuous Castings_机械/仪表_工程科技_专业资料。ASTM B BM Chemical Composition according to ASTM B/BM 1Ni value includes Co. Note: Cu + Sum of Named Elements, % min. Single values, unless. ASTM B/BM Standard Specification for Copper Alloy Continuous Castings. standard by ASTM International, 03/01/ View all product details.

Author: Dosida Grozshura
Country: Venezuela
Language: English (Spanish)
Genre: History
Published (Last): 7 April 2011
Pages: 121
PDF File Size: 14.53 Mb
ePub File Size: 13.20 Mb
ISBN: 973-8-58987-249-4
Downloads: 46622
Price: Free* [*Free Regsitration Required]
Uploader: Samugul

A number in parentheses indicates the year of last reapproval. A superscript epsilon e indicates an editorial change since the last revision or reapproval. This standard has been approved for use by agencies of the Department of Defense.

In such cases the manufacturer shall maintain heat traceability to speci? The values stated in each astk may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the speci? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Current edition approved April 1, Originally approved in The suffix can be used to accommodate composition variations of the base alloy. No further reproductions authorized. Silicon 3, Phosphorus 0.

ASTM B505 SAE 660 Bronze

When tolerances are speci? Materials and Manufacture 6.

The cross sections are the diameter of a round solid, the distance across the? D Yield strength at 0. C used only in the quench-hardened and tempered TQ30 condition.

F As cast or temper asttm. Cooling shall be by b055 fastest means possible that will not cause excessive distortion or cracking. Propeller castings shall be exempt from this requirement. C, C, C, and C may be supplied in the heat-treated condition to obtain 4 the higher mechanical properties shown in Table 9.

  ALLOPLASTYKA STAWU KOLANOWEGO PDF

C are given in Table 2. Actual practice may vary by manufacturer. C is used only in the quench-hardened and tempered TQ30 condition, see Asmt 2. Limits may be established and analysis required for unnamed elements agreed upon between the manufacturer or supplier and the purchaser. When all named elements in Table 10 are analyzed, their sum shall be as speci? Analysis shall be made for residual elements only when speci?

ASTM B / BM – 18 Standard Specification for Copper Alloy Continuous Castings

Mechanical Property Requirements 8. In these cases, mechanical property requirements shall be subject to agreement between the purchaser and the manufacturer.

In addition, heat numbers, or serial numbers that are traceable to heat numbers, shall be marked on all pressurecontaining castings individually weighing 50 lb Pressure-containing castings weighing less than 50 lb Marking shall be in xstm a position as not to injure the usefulness of the casting.

Each continuous casting from which the test bar was taken shall be identi? If all of the test bars from the initial sampling meet the requirements, the lot shall be acceptable. The fractured bars shall be retained for chemical veri?

Dimensions and Permissible Variations Table 3 and Table 4 are to be used in conjunction with Tolerance Table 6 and H505 5, respectively.

If the wall thickness is 1? Sul- Phosfur phorus 0.

In determining copper minimum, copper may be calculated as copper plus nickel. C in the heat-treated condition will not be attained if the lead content exceeds 0. F Chromium content shall be 0. G Iron content shall not exceed nickel content. Other major element chemical requirements: H Chemical requirements for other elements: When castings are produced from alloy ingots of known composition, the sampling interval may be raised to one sample for each lb kg of continuous production of the lot.

This sample may be taken before mechanical straightening. Test bar specimens shall be positively identi? Where castings are heat treated, test bar specimens shall be heat treated with the castings they represent. Each continuous cast bar from which the test bar was taken shall be identi? If a Brinell hardness is required and a tension test is not required, testing shall be in accordance with Test Method E If a Rockwell hardness is required and a tension test is not required, testing shall be in accordance with Test Method E b5055 Applicable to any longitudinal surface or edge.

  CANTIQUE DE NOEL ANTILLAIS PDF

The derived SI unit for force is the newton Nwhich is de?

ASTM B / BM – 12 Standard Specification for Copper Alloy Continuous Castings

Approved April 1, Committee B05 has identi? ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination aastm the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

If you feel that 5b05 comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxasttm service astm.