ATMEGA8 DATENBLATT PDF
Updated the datasheet according to the Atmel new Brand Style Guide. 2. Updated Changes done compared to ATmega8/L datasheet T-AVR/08 . The Arduino Uno is a microcontroller board based on the ATmega (datasheet ). Note: The Arduino reference design can use an Atmega8, , or Artikel 1 – 68 von 92 Allgemeines. Modell; ATmegaPU. Typ; 8-Bit Mikrocontroller. Technologie; AVR RISC Architektur. Ausführung; Watchdog. Gehäuse.
|Published (Last):||26 February 2006|
|PDF File Size:||10.56 Mb|
|ePub File Size:||4.26 Mb|
|Price:||Free* [*Free Regsitration Required]|
It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Duemilanove is the latest in a series of USB Arduino boards; for a comparison with previous versions, see the index of Arduino boards.
The power atega8 is selected automatically. The adapter can be connected by plugging a 2.
ATMEGA 88-20 PU
The board can operate on an external supply of 6 to 20 volts. If supplied with less than 7V, however, the 5V pin may supply less than five volts atega8 the board may be unstable. If using more than 12V, the voltage regulator may overheat and damage the board.
The recommended range is 7 datfnblatt 12 volts. Each of the 14 digital pins on the Duemilanove can be used as an input or output, using pinModedigitalWriteand digitalRead functions. They operate at 5 volts.
Each pin can provide or receive a maximum of 40 mA and has an internal pull-up resistor disconnected by default of kOhms.
In addition, some pins have specialized functions:.
The Duemilanove has 6 analog inputs, each of which provide 10 bits of resolution i. By default they measure from ground to 5 volts, though is it possible to change the upper end of their range using the AREF pin and the analogReference function.
Additionally, some pins have specialized functionality:.
See also the mapping between Arduino pins and ATmega ports. The Arduino Duemilanove has a number of facilities for communicating with a computer, another Arduino, or other microcontrollers.
The Arduino software includes a serial monitor which allows simple textual data to be sent to and from the Arduino board. A SoftwareSerial library allows for serial communication on any of the Duemilanove’s digital pins. The Arduino software includes a Wire library to simplify use of the I2C bus; see the documentation for details.
The Arduino Duemilanove can be programmed datenbltat the Arduino software download. For details, see the reference and tutorials. The ATmega or ATmega on the Arduino Duemilanove comes preburned with a bootloader that allows you to at,ega8 new code to it without the use of an external hardware programmer.
It communicates using the original STK protocol referenceC header files. You can also bypass the bootloader and program the microcontroller through the ICSP In-Circuit Serial Programming header; see these instructions for details.
Rather then requiring a physical press of the reset button before an upload, the Arduino Duemilanove is designed in a way that allows it to be reset by software running on a connected computer.
When this line is asserted taken lowthe reset line drops long enough to reset the chip. The Arduino software uses this capability to allow you to upload code by simply pressing the upload button in the Arduino environment.
This means that the bootloader can have a shorter timeout, as the lowering of DTR can be well-coordinated with the start darenblatt the upload. This setup has other implications.
Arduino – ArduinoBoardDuemilanove
For the following half-second or so, the bootloader is running on the Duemilanove. While it is programmed to ignore malformed data i. If a sketch running on the board receives one-time configuration or other data when it first starts, make sure that the software with which it communicates waits a second after opening the connection and before sending this data. The Duemilanove contains a trace that can be cut to disable the auto-reset.
The pads on either side of the trace can be soldered together to re-enable it. You may also be able to disable the auto-reset by connecting a ohm resistor from 5V to the reset line; see this forum thread for details. The Arduino Duemilanove has a resettable polyfuse that protects your computer’s USB ports from shorts and overcurrent. Although most computers provide their own internal protection, the fuse provides an extra layer of protection.
If more than mA is applied to the USB port, the fuse will automatically break the connection until the short or overload is removed. The maximum length and width of the Duemilanove PCB are 2. Three screw holes allow the board to be attached to a surface or case.
Note that the distance between digital pins 7 dtenblatt 8 is mil 0. This is how you can pronounce the board’s name in proper Italian, download the sound file in the format that better suits you: